OSHA’s Winter Weather Resources

Outdoor work requires proper preparation, especially in severe winter weather conditions. Although OSHA does not have a specific standard that covers working in cold environments, employers have a responsibility to provide workers with employment and a place of employment which are free from recognized hazards, including winter weather related hazards, which are causing or are likely to cause death or serious physical harm to them (Section 5(a)(1) of the Occupational Safety and Health Act of 1970). Employers should, therefore, train workers on the hazards of the job and safety measures to use, such as engineering controls and safe work practices, that will protect workers’ safety and health.

Click Here to go to OSHA’s Winter Weather page.

2019 Fatality #17 / Coal #7

On August 20, 2019, a 20-year-old miner with 27 weeks of mining experience was fatally injured when he fell 40 feet down a shaft, to the concrete floor below. The victim was working with another miner, unloading a refuse kettle attached to an electric hoist, when he went over the unguarded edge of the shaft.

Best Practices: 

• Always use fall protection equipment and safety belts with lines, when working at heights and near openings where there is a danger of falling.
• Have properly designed gates, safety chains, handrails, guards, and ensure covers are securely in place at openings through which persons may fall.
• Always be aware of your surroundings and any hazards that may be present.
• Establish and discuss safe work procedures.
• Train personnel in safe work procedures regarding the use of handrails and fall protection equipment, and ensure their use.
• Conduct workplace examinations in order to identify and correct hazards prior to performing work. Report hazards that you cannot immediately correct to management.

Click here for: MSHA Preliminary Report (pdf) Final Report (pdf).

2019 Fatality #7 / MNM #4

Fatality #8

On May 18, 2019, a 34-year-old plant operator with 8 years of experience received fatal injuries when he was ejected from a man lift basket. The victim was tramming while elevated at 28 feet. The miner was wearing a fall protection harness with a retractable lanyard but it was not secured/tied off to the man lift basket. 

Best Practices: 

  • Always stay connected/tie off.  Always attach the lanyard of the approved fall protection device to the designated attachment point.
  • Use boom functions instead of tram functions to position the platform close to obstacles.
  • Ensure that persons are properly task trained regarding safe operating procedures before allowing them to operate mobile equipment.
  • Do not place yourself in a position that will expose you to hazards while performing a task.
  • Ensure that access gates or openings are closed.

Click here for: MSHA Preliminary Report (pdf), Final Report (pdf).

2019 Fatality #4 / MNM #2

On March 7, 2019, a 46-year-contractor with three years of experience was fatally injured when he lost his balance and fell backwards through a narrow gap between two log washers and landed on a cable tray approximately 12 feet below.  The victim was changing drive belts on a log washer motor when his wrench slipped off of a bolt he was tightening, causing the loss of balance.

Best Practices: 

  • Always use fall protection equipment, safety belts and lines, when working at heights and near openings where there is a danger of falling.
  • Always be aware of your surroundings and any hazards that may be present.
  • Have properly designed handrails, guards, and covers securely in place at openings through which persons may fall.
  • Train personnel in safe work procedures regarding the use of handrails and fall protection equipment during maintenance and construction activities and ensure their use.
  • Conduct workplace examinations in order to identify and correct hazards prior to performing work.

Click here for: MSHA Preliminary Report (pdf), Final Report (pdf).

Fatality #3 for Coal Mining 2017

On February 27, 2017, a 43-year-old plant attendant, with approximately 13 years of experience, was fatally injured when he fell through a 27-inch opening in a plate press.  The victim had climbed a ladder to repair a damaged plate when he fell about 19 feet onto a moving refuse belt.  The victim was found in a transfer chute, approximately 55 feet down the belt from where he had fallen.

Best Practices

  • Provide and maintain safe access to all work areas.  Train miners on how to safely access all work areas.
  • Protect and guard all openings through which persons may fall.  Use fall protection, maintaining 100 % tie off, when fall hazards exist.  See Fall Prevention Safety Target Package.
  • Establish specific policies and procedures for the use of fall protection.
  • Ensure workers are trained in the use of fall protection.  Monitor work practices to ensure fall protection is being properly used.
  • Conduct a risk assessment of the work area prior to beginning any task and identify all possible hazards.  Use the SLAM: Stop, Look, Analyze, and Manage approach for work place safety.

Click here for: MSHA Preliminary Report (pdf), Final Report (pdf).

M/NM Serious Accident Alert

dec-21-2016A miner was trying to determine why clay was not flowing properly by examining a chute that discharged into a screw conveyor. Instead of using a ladder to look inside, he stood on top of the metal screw conveyor cover his foot slipped and he fell approximately three feet to the grating floor hitting his head and suffered serious injuries.

BEST PRACTICES 

  • Identify all potential tripping and falling hazards before working.
  • Look for fall hazards such as unprotected floor openings or edges, shafts, skylights, stairwells, and roof openings.
  • Select, wear, and use the appropriate fall protection equipment for the task.
  • Provide and use appropriate lighting in work areas after dark.
  • Use appropriate ladder for job task.

Download MSHA Alert HERE.

Fatality #14 for Metal/Nonmetal Mining 2016

m14On September 15, 2016, a 60 year old Mechanic, with 28 years of experience, was fatally injured at a Magnesite facility. The victim was seriously injured when he fell while dismounting a front end loader. The victim was hospitalized and died on September 26, 2016.

Best Practices

  • Always use the “Three Points of Contact” method. Use either two hands and one foot, or one hand and two feet when mounting and dismounting equipment.
  • Keep hands free of any objects when making three points of contact.
  • Maintain traction by ensuring footwear is free of potential hazards such as dirt, oil, and grease.  Slip resistant material can be coated to existing foot holds and handrails.
  • Use hoisting materials to transport tools and other objects that may keep hands from being free.
  • Inspect contact areas for slip or trip hazards.
  • Ensure steps and handrails are properly secured and free of defects and debris and always face equipment when mounting or dismounting it.
  • Ensure landing areas are equipped with adequate lighting.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (pdf).