Author: renewcomer

Fatality #19 for Metal/Nonmetal Mining 2013

renewcomerLeave a comment

ftl2013m19On December 4, 2013, a 63-year old lead man with 16 years of experience was killed at a crushed stone mine. The victim initiated a blast and was struck by flyrock from the blast. He was standing 153 feet from the nearest blast hole and was struck by rock as large as 19 inches long by 14 inches wide by 7 inches thick.

 

Best Practices

 

  • Establish and discuss safe work procedures before beginning work. Identify and control all hazards associated with the work to be performed and the methods to properly protect persons. Task train all persons in safe work procedures.
  • Maintain and use all available methods of communication, such as sirens and radios, to warn persons of an impending blast. Establish methods to ensure that all persons are out of the blasting area.
  • Guard or barricade all access routes to the blasting area to prevent the passage of persons or vehicles.
  • Before firing a blast, give ample warning to allow all persons to be evacuated.
  • Clear and remove all persons from the blasting area unless suitable blasting shelters are provided to protect persons from flyrock.
  • Verify that the blasting procedures are effective and being followed at all times.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf).

Fatality #20 for Coal Mining 2013

renewcomerLeave a comment

ftl2013c20On Saturday, November 23, 2013, a 32-year-old longwall shieldman with 5 years of mining experience was killed when he was struck by high pressure hydraulic fluid from a panline valve bank. The victim was advancing shields and the panline when a hydraulic hose extending from the panline to a shield was pinched between a shield pontoon and the mine floor. As the shields and panline advanced, a fitting on the hydraulic hose broke where it was attached to a panline valve bank.

Best Practices
  • Keep all high pressure hydraulic hoses free from pinch points, sharp edges, and abrasive areas.
  • Use whip checks to prevent excessive free motion of hoses at connection points.
  • Ensure proper hose routing to eliminate abrasion damage and exposure to ignition and electrical sources.
  • Do not locate high pressure hoses in travel ways or in areas where miners are regularly exposed to them.
  • Replace hydraulic hoses with hoses identical (length, diameter, pressure rating, etc.) to the original hose.
  • Always assure pressure is removed from any hoses being replaced.
  • Always check for defective hydraulic hoses and replace damaged hydraulic hoses immediately.
  • Train miners on the dangers associated with hydraulic hoses on long wall faces and in proper maintenance procedures for the hydraulic system.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf).

Fatality #18 for Metal/Nonmetal Mining 2013

renewcomerLeave a comment

ftl2013m18On November 18, 2013, a 33-year old contract electrician foreman with 14 years of experience was injured at a crushed stone mine. The victim was working in a 480-volt electrical enclosure, pulling cable for a new pump that was being installed, when he contacted energized conductors. He was transported to a hospital where he died on November 22, 2013.

Best Practices

  • Ensure that persons are trained on all electrical tests and safety equipment necessary to safely test and ground the circuit where work is to be performed.
  • Positively identify the circuit on which work is to be conducted.
  • De-energize power and ensure that the circuit is visibly open for circuits being worked on and circuits near the work area.
  • Lock and Tag! Place YOUR lock and tag on the disconnecting device.
  • Use properly rated Personal Protective Equipment (PPE) including Arc Flash Protection such as a hood, gloves, shirt, and pants.
  • Ensure ALL electrical components in the enclosure are de-energized by testing for voltage using properly rated test equipment.
  • Install warning labels on the terminal covers of bottom feed circuit breakers warning that “Bottom terminal lugs remain energized when the circuit breaker is open.”

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #16 & 17 for Metal/Nonmetal Mining 2013

renewcomerLeave a comment

ftl2013m1617On November 17, 2013, a 33-year old powderman trainee with 5 weeks of experience and a 59-year old shift supervisor with 36 years of experience were killed at a silver mine. The two miners were in an area of the mine where explosives had been detonated the day before. Other miners working in the area were able to evacuate. Mine rescue teams entered the mine, found the two victims, and brought them to the surface. During the recovery operation, rescue teams detected fatal levels of carbon monoxide. Twenty miners were taken to the hospital and three were kept overnight.

Best Practices

  • Conduct effective workplace examinations. Identify all hazards and take action to correct them.
  • Ensure all active working areas are ventilated prior to allowing miners to work in those areas.
  • Monitor gasses as frequently as necessary to determine the adequacy of control measures.
  • Use properly maintained and calibrated gas detection instruments with alarms for concentrations outside of safe limits that are audible and visual.
  • Ensure all miners are trained to recognize all potential hazards and emergency procedures, including evacuation procedures.
  • Dispose of damaged or deteriorated explosive material in a safe manner in accordance with the instructions of the manufacturer.

Click here for: MSHA Preliminary Report (pdf)

Fatality #19 for Coal Mining 2013

renewcomerLeave a comment

ftl2013c19

On November 4, 2013, a 36 year-old longwall chief, with 16 years of experience, was killed while shoveling loose coal and rock between the coal face and the pan line on a longwall section. The victim received crushing injuries when a solid piece of coal and cap rock fell from the coal face, striking and pinning him against the face side of the pan line. The coal/rock combination measured approximately 4 feet and 10-inches long, by 2 feet and 3 inches wide, and up to 24 inches thick.

Best Practices

  • Conduct a thorough examination of the roof, face, and ribs, including a visual examination and a sound and vibration test prior to miners being assigned to work or travel through an area.
  • Correct hazardous roof, face, or rib conditions before any work or travel is permitted in the affected area.
  • Use a bar of suitable length and design for removing loose or unconsolidated material.
  • Support the exposed longwall roof, face, and ribs by mechanical means in the immediate work area.
  • Train all miners in hazard recognition and safe work practices that are assigned to perform work on the longwall face.
  • Apply additional safety precautions in areas where geological changes and anomalies in strata are present.
  • Post a certified foreman at the work area when maintenance is being performed.
  • De-energize the face conveyor, notify the headgate operator, and disconnect power at the control station while work is being performed on the face conveyor (pan). Do not energize the conveyor until all persons are off the face side of the conveyor and the conveyor is supported adequately from inadvertent movement.

Click here for: MSHA Preliminary Report (pdf)

Fatality #15 for Metal/Nonmetal Mining 2013

renewcomerLeave a comment

ftl2013m15On November 7, 2013, a 46-year old equipment operator with 27 years of experience was killed at a granite mine. The victim was operating a haul truck when it veered off the left side of a haul road and traveled through a berm. The haul truck went over an embankment and overturned in a settling pond.

Best Practices

  • Provide and maintain adequate berms or guardrails on the banks of roadways where a drop-off exists.
  • Conduct pre-operational checks to identify and correct any defects that may affect the safe operation prior to operating mobile equipment.
  • Always wear a seat belt when operating self-propelled mobile equipment.
  • Maintain control of self-propelled mobile equipment while it is in motion.
  • Operate mobile equipment at speeds consistent with the conditions of roadways, tracks, grades, clearance, visibility, curves, and traffic.
  • Stay alert while operating mobile equipment.
  • Ensure traffic rules, signals, and warning signs are posted and obeyed.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #14 for Metal/Nonmetal Mining 2013

renewcomerLeave a comment

ftl2013m14On October 17, 2013, a 52-year old electrician with 5 years of experience was injured at a cement operation. The victim was standing on a step ladder, pulling cable in a cable tray. The mounting bracket for the tray broke loose from the wall and the tray struck the step ladder. The victim fell 5 feet from the ladder, striking his head on the concrete floor. The victim was transported to a hospital where he died on October 19, 2013.

Best Practices
 

  • Follow the manufacturer’s recommendations when installing a cable tray on a supporting structure.
  • Ensure that the correct anchors are used and that the supporting structures are adequate when installing a cable tray.
  • Always be aware of your surroundings and any hazards that may be present.
  • Properly position ladders used to reach elevated areas.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf).

Fatality #18 for Coal Mining 2013

renewcomerLeave a comment

ftl2013c18On Friday, October 11, 2013, a 59-year-old shuttle car operator, with approximately 22 years of mining experience, was killed when a shuttle car struck him. The victim was in the crosscut between the No. 6 and No. 7 entries. This crosscut and adjoining entries were being used to gain access to rooms being mined on the right side of the section.

Best Practices

  • Use proximity detection systems to protect personnel from accidents of this type. See the proximity detection single source page on the MSHA web site.
  • Always ensure that visibility is not obstructed in the direction of travel and across the equipment being operated.
  • Use transparent curtain for check and line curtains in the active face areas.
  • Sound audible warnings when the equipment operator’s visibility is obstructed, such as when making turns, reversing direction, or approaching ventilation curtains.
  • Come to a complete stop and sound an audible warning before proceeding through ventilation controls.
  • Ensure the sound level of audible warnings is significantly higher than that of the ambient noise.
  • Shine equipment lights in the direction of travel when operating haulage equipment.
  • Never position yourself in an area or location where equipment operators cannot readily see you.
  • Always communicate your position and intended movements to mobile equipment operators.

For more information related to struck-by equipment accidents, view the following link: MSHA – Safety Targets Programs – Hit By Underground Equipment at www.msha.gov

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf).

Fatality #17 for Coal Mining 2013

renewcomerLeave a comment

ftl2013c17On Sunday, October 6, 2013, at approximately 2:30 a.m., a 44-year old bulldozer operator, with approximately 10 years of experience, sustained fatal injuries when the dozer he was operating went over the edge of a highwall.

Best Practices

  • Task train miners adequately on the equipment they will operate.
  • Train all employees on safe work procedures, hazard recognition, and hazard avoidance.
  • Maintain a safe distance from the edge of the highwall.
  • Ensure adequate berms are in place.
  • Be familiar with your work environment. Before beginning work, look at the area, walk around it, and plan the safest way to move the material and maneuver the equipment.
  • Ensure illumination is adequate when work is performed during non-daylight hours.
  • Maintain control of equipment at all times during operation.
  • Ensure that personnel operating mobile equipment always wear a seat belt.

Click here for: MSHA Preliminary Report (pdf)