Author: renewcomer

Fatality #15 for Coal Mining 2014

renewcomerLeave a comment

c15On Tuesday, December 16, 2014, a 34-year-old repairman, with approximately 15 years of mining experience, was killed when struck by a ram car while he was walking inby toward the face of the No. 7 entry. The ram car operator moved the ram car into the No. 7 entry with the batteries positioned outby the face area and then traveled towards the face area, striking the victim with the left side, trailer end of the ram car.

Best Practices

  • Use proximity detection systems to protect personnel from accidents of this type.  See the proximity detection single source page on the MSHA web site.
  • Ensure that visibility is clear in the direction of travel and across the equipment being operated.
  • Use transparent curtain for checks and line curtains in the active face areas.
  • Sound audible warnings if the equipment operator’s visibility is obstructed, when making turns, reversing direction, or approaching ventilation curtains.  Ensure the sound levels of audible warnings are significantly higher than ambient noise.
  • Come to a complete stop and sound an audible warning before moving equipment through ventilation controls/curtains.
  • Operate lights in the direction of travel when operating haulage equipment.
  • Position yourself in an area or location where equipment operators can readily see you and confirm eye contact with the operator.
  • Require the use of personal strobe lights for any foot traffic inby the tailpiece.  Position personal strobe lights on the back of hard hats or equivalent areas and use reflective materials to ensure maximum visibility.
  • For more information related to struck-by equipment accidents, view the following link: MSHA – Safety Targets Programs – Hit By Underground Equipment at www.msha.gov

Click here for: MSHA Preliminary Report (pdf)

Fatality #21 for Metal/Nonmetal Mining 2014

renewcomerLeave a comment

m21On November 18, 2014, a 42-year-old contract supervisor with 19½ years of experience was killed at an alumina operation.  A crane was lifting a 2,500 pound door to be installed on a filtrate tank.  The welded lifting eye on the door broke loose and the door fell, pinning the victim on the concrete floor.

Best Practices

  • Establish and discuss safe work procedures before beginning work.
  • Identify and control all hazards associated with the work to be performed.
  • Task train all persons to understand safe job procedures and to stay clear of suspended loads.
  • Use welded lifting eyes that are specifically intended for lifting and adequately rated for the loads being lifted.
  • Use certified welders and good quality welds when attaching lifting eyes or lugs.
  • Ensure the weld metal is compatible with the base metal of the connecting components and thoroughly clean any rust or scale from a surface prior to welding.
  • Carefully inspect all rigging prior to each use.
  • Attach taglines to loads that may need steadied or to be guided while suspended.
  • Avoid extreme side loading on a lifting eye or lug unless it is designed to handle such loading.
  • Monitor persons routinely to determine safe work procedures are followed.

Click here for: MSHA Preliminary Report (pdf)

November 2014 Impact Inspections

renewcomerLeave a comment

MSHA-logo

The U.S. Department of Labor’s Mine Safety and Health Administration today announced that federal inspectors issued 199 citations and 19 orders during special impact inspections conducted at 10 coal mines and six metal and nonmetal mines in November.

The monthly inspections, which began in force in April 2010, involve mines that merit increased agency attention and enforcement due to their poor compliance history or particular compliance concerns.

Click here for: MSHA link to spreadsheet (pdf).

December 6 is National Miners Day

renewcomerLeave a comment

Miners-Day-Poster1web-493px-x-270px-

December 6th is #NationalMinersDay designated by Congress in 2009 as a day to recognize and honor the contributions and sacrifices of our nation’s miners – past, present and future.

Did you know that the U.S. has nearly 375,000 miners working in almost 14,000 mines? Our nation’s miners extract nearly 100 types of minerals from the ground, which are used to heat our homes, carry electricity, build bridges, keep highways clear in winter, and provide the raw materials for hundreds of products – from computers to cosmetics to cooking utensils.

Join us in thanking our nation’s miners for their extraordinary contributions and sacrifices.

➨ Learn more: www.msha.gov/minersday

Fatality #20 for Metal/Nonmetal Mining 2014

renewcomerLeave a comment

m20aOn October 10, 2014, a 66-year-old contract truck driver with approximately 11 years of experience was killed at a cement operation.  The driver was inside a loading rack closing the hatch on top of a bulk tanker truck.  When the victim raised the rack to access the hatch, he fell between the rack and rounded side of the truck and then fell to the ground.

Best Practices

  • Establish traffic patterns to ensure safe alignment of vehicles with access equipment.
  • Identify and control all hazards associated with the work to be performed and use methods to properly protect persons.
  • Ensure that persons are trained, including task-training, to address the hazards associated with the work being performed.
  • Always use fall protection when working where a fall hazard exists.
  • Always be aware of your surroundings and any hazards that may be present.

Click here for: MSHA Preliminary Report (pdf)

Fatality #19 for Metal/Nonmetal Mining 2014

renewcomerLeave a comment

m19aOn September 26, 2014, a 55-year-old maintenance mechanic with approximately 2 years of experience was killed on the surface of an underground salt mine.  The victim was performing maintenance on a forklift in a mill building when the forklift moved forward, pinning him against a wooden support pole.

Best Practices

  • Conduct a pre-operational check to identify and correct any defects that may affect the safe operation prior to operating mobile equipment.  Remove the mobile equipment from service if any defective items are not corrected.
  • Establish and discuss safe work procedures before beginning work. Identify and control all hazards associated with the work to be performed and use methods to properly protect persons.
  • Ensure that persons are trained, including task-training, to address the hazards associated with the work being performed.
  • Block and secure equipment against motion before performing maintenance.
  • Follow the equipment manufacturers recommended maintenance procedures when performing repairs to machinery.
  • Ensure that equipment control switches are in the off position and the brake is set before performing maintenance.
  • Always be aware of your surroundings and any hazards that may be present.

Click here for: MSHA Preliminary Report (pdf)

October 2014 Impact Inspections

renewcomerLeave a comment

MSHA-logoThe U.S. Department of Labor’s Mine Safety and Health Administration announced that federal inspectors issued 127 citations and six orders during special impact inspections conducted at 12 coal mines in October.
The monthly inspections, which began in force in April 2010 after the explosion at the Upper Big Branch Mine, involve mines that merit increased agency attention and enforcement due to their poor compliance history or particular compliance concerns.
Since April 2010, MSHA has conducted 835 impact inspections and issued 13,267 citations, 1,200 orders and 55 safeguards.

Click here for: MSHA link to spreadsheet (pdf).

Fatality #14 for Coal Mining 2014

renewcomerLeave a comment

14c14On Monday, November 10, 2014, at approximately 9:35 p.m., a 49-year-old section foreman with 27 years of mining experience was killed when he was struck by a large rock that measured 5 feet by 3 feet by 13 inches thick.  The victim was operating the roof bolting machine on the 2 North section in the No. 2 entry at the time of the accident.  The rock fell inby the last full row of permanent roof supports and between the automated temporary roof support (ATRS) and the left rib.

Best Practices
  • Perform a visual examination of the roof, face, and ribs immediately before any other work is started in the area.
  • Be alert to changing conditions, especially after activities that could cause roof disturbance.
  • While under supported roof, perform sound and vibration tests where roof supports are to be installed.
  • Adequately support or scale down any loose roof or rib material from a safe location.
  • Ensure that ATRS systems on all roof bolting machines are maintained in good working condition and set firmly against the mine roof before installing new roof supports.
  • Ensure ATRS are set within 5 feet of permanent support as well as within 5 feet of the rib line.
  • Stay under the roof bolting machine canopy when working in the area between the ATRS and the last row of permanent roof support.
  • Ensure that the approved roof control plan is followed and is suitable for the geologic conditions encountered at the mine.  If conditions change and cause the plan to no longer be suitable, the plan must be revised to provide adequate support for the control of the roof face and ribs.

Click here for: MSHA Preliminary Report (pdf)

Fatality #13 for Coal Mining 2014

renewcomerLeave a comment

FTL14c13aOn Saturday, October 18, 2014, at approximately 10:05 p.m., a contractor truck driver with over 5 years of truck driving experience was killed while operating a rock truck. The driver was removing top soil ahead of the East Elk Pit when he drove off a highwall and fell approximately 240 feet.

Best Practices
  • Operate equipment in a manner that is consistent with conditions of roadways, grades, clearance, visibility, traffic, and the type of equipment used.
  • Standardize and post traffic rules, signals, and warning signs.
  • Provide and maintain adequate berms and other barriers that are at least mid-axle high on the banks of roadways where a drop off exists.
  • Train all employees on the equipment they operate, on safe job procedures, hazard recognition, and on hazard avoidance.
  • Maintain control of equipment at all times during operation.  Know the truck’s capabilities, operating ranges, load-limits, and safety features.
  • Monitor work activities and examine work areas to assure safe work practices are followed.
  • Monitor contract employees adequately at all job sites to ensure that safe work procedures are being followed.
  • Conduct pre-operational checks to identify and repair any defects that may affect the safe operation of equipment before it is placed into service.

Click here for: MSHA Preliminary Report (pdf)