Metal/Nonmetal

Fatality #15 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On August 14, 2010, a 23 year-old dredge operator with 4 years of experience died at a sand and gravel dredge operation. The victim and another miner were pulling a small boat from a dredge pond onto a boat trailer attached to a pickup truck. When the boat slipped back into the water, the victim attempted to retrieve it and drowned.

Best Practices
  • Wear a life jacket where there is a danger from falling into water.
  • Review procedures to ensure all possible hazards have been identified and appropriate controls are in place to protect miners before beginning work.
  • Develop procedures for loading and unloading boats in dredge operations and train all persons.
  • Inspect equipment, including the winch and cable, prior to use and maintain in a safe condition.
  • Attach the trailer winch rope securely to the boat prior to removing from the water.
  • Ensure that persons working around water receive training for swimming.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf)

Fatality #13 & #14 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On August 12, 2010, a 38 year-old maintenance technician with 3 years of experience and a 47 year-old operations miner with 21 years of experience died at an underground gold mine. They were working from the top of a conveyance in a 16-foot diameter ventilation shaft attempting to locate and free a blockage in a 24-inch-diameter aggregate delivery pipe. While the conveyance was near the 820 foot level, the entire pipe from the shaft collar to the 860 level broke away and fell to the bottom at the 1330 foot level. The pipe struck the conveyance as it fell, causing the hoist drum to break away from its support base. The victims were found at the bottom of the shaft.

Best Practices
  • Routinely examine pipe support structures for indications of excessive corrosion and cracked, missing, or damaged: clamps, brackets, support beams, and connections.
  • Conduct periodic visual and non-destructive examination on couplings and pipes for corrosion, abrasion thinning, cracking, and loose connections.
  • Inspect and test process monitoring systems to ensure safety controls are functioning properly.
  • Perform construction and maintenance in accordance with design drawings and specifications.
  • Minimize exposure to hazards by using equipment such as air cannons and vibrators to prevent or clear blockages.
  • Ensure that miners are in a safe position to avoid falling objects or materials.

Click here for: MSHA Preliminary Report (pdf),  MSHA Investigation Report (pdf), Overview (powerpoint), Overview(pdf).

Fatality #12 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On June 20, 2010, a 52 year-old mechanic with 8 years of experience was fatally injured at a surface copper operation. A ½ ton pickup truck had parked in front of a 240 ton haul truck that was also parked. The haul truck pulled forward and struck the pickup truck fatally injuring the driver and seriously injuring another miner.

Best Practices

  • Do not park smaller vehicles in a large truck’s potential path of movement.
  • Before moving mobile equipment, be certain no one is in the intended path, sound the horn to warn possible unseen persons, and wait to give them time to move to a safe location.
  • Ensure all persons are trained to recognize work place hazards, specifically the limited visibility and blind areas inherent to operation of large equipment and the hazard of mobile equipment traveling near them.
  • Establish procedures that require smaller vehicles to maintain a safe distance from large mobile equipment until eye contact is made or approval to move closer is obtained from the mobile equipment operator. Provide training in these procedures.
  • Install cameras and collision avoidance systems on large trucks to protect persons.
  • Regularly monitor work practices and reinforce the importance of them. Take immediate action to correct unsafe conditions or work practices.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview(powerpoint), Overview(pdf), Spanish Fatalgram (pdf)

Fatality #11 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On June 18, 2010, a 29 year-old contract miner with 6 years of experience was fatally injured at an underground silver mine. The victim was scaling loose ground in a stope when he was struck by falling material approximately 3½ feet long by 2½ feet wide by 2 feet thick.

Best Practices

  • Examine, sound, and test for loose ground in areas before starting to work, after blasting, and as ground conditions warrant.
  • Train all persons to scale loose material safely.
  • Communicate unsafe ground conditions to all affected miners.
  • Perform manual scaling from a location which will not expose persons to injury from falling material.
  • When manually scaling, use scaling bars of a length and design that will allow the removal of loose material without exposing persons to the risk of injury.
  • Install ground support where conditions warrant.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf), Spanish Fatalgram (pdf)

Fatality #10 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On June 12, 2010, a 46-year-old contractor welder was fatally injured at a crushed stone operation. He was preparing to weld on an overhead ventilation duct. The victim was using a ladder to access the duct when he fell over a handrail approximately 45 feet to the ground.

Best Practices

  • Always use fall protection when working where a fall hazard exists.
  • Position ladders to ensure their stability and to eliminate trip hazards.
  • Always face the ladder when climbing or working from a ladder.
  • Do not lean to reach items while standing on a ladder.
  • Always maintain three points of contact with the ladder when climbing.

Click here for: MSHA Preliminary Report (pdf), MSHA Investigation Report (pdf), Overview (powerpoint), Overview(pdf), Spanish Fatalgram (pdf)


Fatality #9 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On May 28, 2010, a 59-year-old supervisor with 20 years of experience was fatally injured at an underground gold mine. The victim and another miner entered a blast area when a misfire detonated without warning. The other miner was injured and hospitalized.

Best Practices

  • Follow the manufacturers’ guidelines for the storage and usage of explosives.
  • Keep explosives storage areas clean, dry and orderly.
  • Properly rotate explosive stock to use oldest stock first.
  • Never use damaged/deteriorated/outdated explosives, initiation devices, or blasting agents.
  • Wait a minimum of the required times before entering the blast area when either a misfire and/or burning explosives are a possibility.

Click here for: MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf),  Spanish Fatalgram (pdf)

Fatality #8 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On May 26, 2010, a 28 year-old contract miner with 10 weeks of mining experience was fatally injured at an underground uranium mine. The victim was scaling a rib when he was struck by falling material approximately 11 feet high, 15 feet wide and 4 inches to 30 inches thick.

Best Practices

  • Always examine, sound and test for loose ground in areas before starting to work, after blasting, and as ground conditions warrant.
  • Train all persons to scale loose material safely.
  • Always perform manual scaling from a safe location.
  • When manually scaling, use scaling bars of a length and design that allow the removal of loose material without exposing the persons performing the work.
  • Install ground support in ribs where conditions warrant.

Click here for: MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf), Spanish Fatalgram (pdf)

Fatality #7 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On May 24, 2010, a 61-year-old maintenance foreman with 32 years of experience was fatally injured at a crushed stone operation. The victim entered a vertical roller mill without locking out the electrical power switch. The mill was started with the victim in the mill.

Best Practices

  • Always follow established lock-out and tag-out procedures.
  • Never rely on others to place your lock on electrical power switches.
  • Always post warning notices at the power switches.
  • Never enter machinery without ensuring the energy source is locked out.
  • Always test to ensure power is off after locking out.
  • Maintain power switch lock out mechanisms to function properly.

Click here for: MSHA Investigation Report (pdf), Overview (powerpoint), Overview (pdf), Spanish Fatalgram (pdf)

Fatality #6 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On May 14, 2010, a 35 year-old mechanic/welder with 4 years of experience was fatally injured at a cement operation. The victim was using an oxy- acetylene torch to cut a damaged drill steel to salvage the drill bit. The drill steel exploded causing metal fragments to strike the victim.

Best Practices

  • Always examine materials before applying heat, cutting or welding.
  • Never apply heat to materials without ensuring that flammables/combustibles/explosive materials are not present.
  • Always examine materials with hollow spaces or cavities to ensure gases can vent before applying heat.
  • Never apply heat to materials where pressure build up is possible.

Click here for: MSHA Investigation Report(pdf), Overview(powerpoint), Overview(pdf), Spanish Fatalgram (pdf)

Fatality #5 for Metal/Nonmetal Mining 2010

renewcomerLeave a comment

On May 5, 2010, a 21 year-old old contract driller with 1 year of experience was fatally injured at a crushed stone operation. The victim was repositioning a truck mounted drill. He lowered the mast and raised the leveling jacks to move the drill. The drill then rolled down a grade and struck him.

Best Practices

  • Maintain parking brakes to ensure proper function.
  • Always set parking brakes when leaving a vehicle unattended.
  • Ensure parking brake will hold the vehicle before exiting cab.
  • Use tire chocks when parking equipment on grades.
  • Never attempt to enter the cab of a runaway vehicle.

Click here for: MSHA Investigation Report(pdf), Overview(powerpoint), Overview(pdf), Spanish Fatalgram (pdf)